Vimble 3 Handheld 3-Achsen-Smartphone-Gimbal-Stabilisator mit Stativ

Vimble 3 is not compatible with action cameras because their length is not enough to have them mounted firmly in the adapter while using. Also, they could not be balanced before switching Vimble 3 on due to the lighter weight.
If you want to mount action camera on the Vimble 3, please try to find third party mounting plate as shown below, and put them together on the Vimble 3.

1) Low power
- Normally, we could figure out from the indicator, which will flashes with red light in three times.
2) Protection status
- The gimbal’s handle is rotate rapidly->Hold the gimbal with our hand or place it on the desk with a tripod.
- The temperature for the motors are too hot(55°).
- Normally, it is caused by the smartphone not being properly balanced. ->Before turning the gimbal on, please make sure the smartphone is installed and balanced properly with gimbal.
- The motors are excessive load->Before turn on the gimbal, please make sure the smartphone were installed and balanced properly. Check whether there is something stuck into the locker.
- The smartphone is not installed on the gimbal or removed from the adapter.

Find USB cable provided to connect to the USB port on Vimble 3, and connect the other end of USB cable to charger adapter (not included, mobile charger adapter is compatible), as shown below.
Please note: Vimble 3 does not support quick charger.
Charging the battery with 5V/2A output adapter , it will take around 2.5 hours. The indicator is solid red while charging. When the battery is fully charged, it turns to green.

After fully charged the battery, when balanced the smartphone in landscape properly, then put the gimbal on the flat surface with a tripod, it could be used around 10 hours.

Android phones support it, but iPhone does not.

Please install and balance the smartphone with gimbal properly, and make sure the smartphone is already closest with the phone adapter, please keep the clip with Logo facing up.

When the gimbal is on, press mode button abd On-Screen Icons button at the same time and let go after hearing a beep. Initialization will be finished when the indicator flashing with green light-green light constant on-breathing light. And then single tap the power button to wake up.

Method One: Double tap the M button
Method Two: Manually turn clockwise

After unfolded the gimbal, hold the handle with one hand and the other hand hold the ring above the handle (Please refer to the picture below), and pull it up or retract it directly. The maximum length of the handle is 198mm.
Two ways for selfie:
Method One:
Turn on the Bluetooth of smartphone, and find Vimble 3 in the Bluetooth settings, then make connection. Open native camera of smartphone, switch to front camera with triple tap the trigger button, extend the extension rod, then click Bluetooth shutter button on Vimble 3 to complete selfie.
Method Two:
Turn on the Bluetooth of smart phone and make connection with Feiyu On App(Please make sure the gimbal’s Bluetooth did not connected in the smartphone’s Bluetooth settings). Triple tap the trigger button to switch to front camera or rear camera, extend the extension rod, then click Bluetooth shutter button on Vimble 3 to complete selfie.

The function of joystick is to control rotation of smartphone in four directions.

The speed or directions of joystick could be set up in Feiyu On App. Below is the interface in the App for your reference:

Press and hold the bottom trigger button to enter the lock mode, release the trigger button to return to the previous mode.

Press and hold the upper trigger button to enter the flashing mode, and release the trigger button to return to the previous mode.

Android version does not include that mode because part of Android phones could not perform that function.
Note: slow motion function is also not included in part of iPhones which has low configuration, like iPhone5S or iPhone 5.

Please turn the gimbal on, and upgrade the firmware by App again. When upgrading, please make sure the gimbal always on, and keep the phone on App’s interface.

Please try the following steps:
1) Forget the device or cancel pairing in the Bluetooth settings of smartphone, close the Bluetooth of smartphone and open it again, making sure the Bluetooth signal of gimbal is not connected in the smartphone’s Bluetooth settings
2) Please reboot the gimbal, and run the Feiyu On App to connect again

There will be limitation for tilt axis, the available rotated angle is ±40, the pan axis shaking is cause by the tilt working in the limitation angle.

1) Please make sure Portrait Orientation Lock in iPhone were turn off, kindly see the picture below
2) Please make sure you were paired the Bluetooth with Feiyu On App properly

1) Make sure the battery for the gimbal is not ran out off
2) Do not charging the gimbal’s battery during the upgrade process
3) Do not turn off the App during the upgrade process
4) Do not turn off the gimbal during the upgrade process

The Android version of Feiyu ON APP currently does not support recording 60FPS videos under 4K resolution. It is recommended to use the phone's stock camera for recording 4K60FPS videos after pairing the Bluetooth between gimbal and the phone.