FeiyuTech Vimble 2S Helps to Provide More Perspectives, Film More Stable Video, Shoot Professional Style Clips and Edit Video with Special Effect and Stickers
Hurry up! Sale Ends indayshoursminssecs
Compatible Dimension: Smartphone width ranges from 57-84mm(about 7inch);
Payload: Landscape mode:0.46lb/210g; Portrait mode: 0.44lb/200g
Compatible Phone: Vimble 2S is compatible with iPhone 11 or other iPhone below, HUAWEI P30/Nova 4/ Vivo X23 , OPPO R9S etc. Android smartphone and other smartphones which the width is between 57-84mm
|Battery type||7.4 V, 1300MAH, 9.62 Wh, Built-in Rechargeable Battery. Battery could be charged by power bank with a USB cable when using it.|
|Theoretical battery time||12h(tested with well-balanced status before powering on, and do not charge smart phone while working)|
|Charging battery||≥ 2h,recommending using 5V/2A adapter for charging battery (quick charger is banned from charging). The indicator is red while charging. When the battery is fully charged, it turns to green.|
|Charging smartphone||Output voltage: DC 5V;MAX Electric Current Output: 600 mA (could charge smart phone for approx. 2 hours while it is shooting)
For instance: When the power of iPhone 6 Plus is out, the batter of Vimble 2 is full, iPhone could be charged to 60%
|Material||PC, PA6 and other materials which are of high-strength, doing best in temperatures within -45 to 135 degrees Celsius.|
|Controllable range||Tilting range:320°(with motor lock)
Rolling range:320°(with motor lock, can rotate 360°under All follow mode)
Panning range:320°(with limited)
|Weight||428g(include built-in battery, NOT include phone )|
|Balance before power on||Vimble 2S has tilt&roll axis motor lock(as image shows) please unlock them before mounting smartpone.
Landscape mode: Balance mobile phones weighed differently by moving cross arm left to right.
Portrait mode: Rotating the quick-release adapter vertically and putting in smartphone, Simply Balance with sliding the smartphone up and down.
|Power ON/OFF||Power ON/OFF:Long-press the function button until the green light is on with a beep then release it. (Apporx. 2~3 s)|
|Switch between Portrait/ landscape||Option 1:When in landscape mode, pull smart phone outward about 10 mm then rotate the quick-release adapter 90 degrees so that it could change to portrait mode, as shown below.
Option 2:Operating with function button and trigger button (Only when tilt axis motor is placed on the right side)
Steps:Hold the gimbal horizontally, long pres and hold the trigger button then single tap the function button. Reset:Double click trigger button to exit portrait mode.
|Extendable rod||The extendable handle could be extended and retractable for selfie no matter whether Vimble 2 is on or off. Its max length is 183mm.|
|Working mode & Button operation||Function button operations:
Option 1: Control original camera/ beauty cam APP to take picture /record video(connect smartphone to on Feiyu ON APP by bluetooth).
Option 2: Control Feiyu ON APP
|Operational Function For Users||
|Extended port||1/4 inch screw hole at the bottom of handle to mount Tripod or other accessories.|
|Standard accessories||Micro USB cable*1(charging cable for gimbal)，phone charging cable*3(Micro-Micro,Micro-Type C,Micro-Lightning)，anti-lost rope*1，MT mini tripod*1,EPP carrying bag*1|
|Optional accessories||Extendable rod(with 1/4inch screw hole ),universal tripod with 1/4 screw hole,handle with power supply.|
When used in landscape mode, the max payload is 210 g, whilst in portrait mode, the max payload is 200 g.
Note： ⒈Large-size smartphone such as iPhone 11Pro Max 226g,HUAWEI MATE20X 232g which is beyond max payload, is unavailable to balancing. Smartphone with width over 85mm can not be attached on quick-release adapter such as HUAWEI Honor NOTE10.
⒉While using smartphone such as iPhone 11Pro max，iPhone 11，HUAWEI P30 and take video with wide-angle lenses, the roll axis will be captured in footage, we suggest you use normal lens.
Vimble 2S is not directly compatible with action cameras. If you want to mount action camera on, try to find third party mounting plate to put it on. As the picture shown.
1) Low power
- Normally, we could figure out from the indicator , which will flashes with red light in three times.
2) Protection status
-The gimbal’s handle is rotate rapidly— Hold the gimbal with our hand or place it on the flat surface with a tripod.
-The temperature for the motors are too hot(55°)— Normally, it will cause by the smartphone did not balanced properly.
-The motors are excessive load— Before turn on the gimbal, please make sure the smartphone were installed and balanced properly. Check whether there is something stuck into the locker.
It will take around 3 hours to fully charged the battery. Recommending using 5V/2A adapter for charging battery (quick charger is banned from charging).
The indicator is red while charging. When the battery is fully charged, it turns to green.
The indicator is in red and green, maybe poor contact happened or cable inside was worn due to improper operations in transportation. Please unplug USB cable and plug it in again. If same thing happened, please send the gimbal to us for repair.
If the headphone jack of your smart phone is not blocked by Vimble2S, you can directly connect external microphone with smart phone to record. As the picture shown.
Headphone extension cord is recommended since it is light-weight. If video and audio wires for Live Broadcast were used, it would be better to purchase extended wire holder to avoid interference to gimbal.
The telescoping hand could be extended and retractable for selfie no matter whether Vimble 2 S is on or off. Its max length is 180mm.
Two ways for selfie: Method One: open bluetooth of smart phone, and find Vimble2S in the bluetooth list then make connection. Open original camera of smart phone, switch to front camera, extend telescoping hand, then click bluetooth shutter button on Vimble2S to complete selfie. Method Two: open bluetooth of smart phone and make connection with Feiyu On App. Triple clicking function button to switch to front camera or rear camera, extend telescoping hand, then click bluetooth shutter button on Vimble2S to complete selfie.
Function button could be found on the handle, as shown below. It is used for powering on/off gimbals and changing working modes.
Changing working modes operations: Single tap: Switching between pan mode (Default mode) and lock mode.
Double tap: Pan and tilt mode(follow mode),Entering Feiyu ON APP can customize this operation.
Triple tap: All follow mode(3-axis follow mode),Entering Feiyu ON APP can customize this operation.
Penta tap: Initializing the gimbal in order to get correct attitude parameters when it is not level or in abnormal status.
Long press：Power ON/OFF
Option 1: Control with original camera/ beauty cam APP to take picture /record video(connect smartphone to on Feiyu ON APP by bluetooth).
Option 2: Control with Feiyu ON APP
Single tap：Control photo/video recording(under its current mode).
Double tap：switch between photo /video recording.
Triple tap：switch camera front and rear camera.
Long press：start video recording in photo mode.
When successfully connects with Feiyu ON APP, push focus button up (W direction) to zoom in at a constant speed; push focus button down (T direction) to zoom out at a constant speed.
Long press and hold: Enter lock mode. Release it to go back to the previous mode.Entering Feiyu ON APP can customize this operation.
Double tap: Reset the gimbal, it will go back to panning mode no matter what current mode is, and three axis are reset to default position.
Instruction of initialization: The LED is in solid blue after fifth tapping function button. The gimbal automatically detect whether or not it is placed on a static flat surface.
Initialization will be done automatically (LED flashes blue three times to indicate initialization is done) once the gimbal has detected that it is placed on a static flat surface.
Otherwise, the gimbal is keeping detect and wait. When initialization is done successfully, single tap function button to wake up the gimbal.
When Vimbe2 is off, press bluetooth shutter,function button and trigger button at the same time for about 2-3 seconds, the indicated will flashes blue light in a group of three.
Next, restart the gibmal. to power on gimbal so that all the bluetooth pairing info is cleared.
Please try the following steps:
1.Don't run the App, pair gimbal in the bluetooth list of smart phone, and check if bluetooth shutter button could control the volume.
2.Forget the device or cancel pairing in the bluetooth list of smart phone, close the bluetooth of smart phone and open it again, making sure the bluetooth signal of gimbal is not connected or paired.
3.If it acts the same after doing the steps as above, please restart the smartphone. And run the App to connect again.