Feiyu G6 Max

Charging the gimbal via USB cable and power souse, it takes about 3 hours to fully charged the batteries with a 5V/2A charger.
The charging icon(Lightning icon) will be show up while charging, after fully charged, the charging icon will became 4 pcs of bars.

NOT waterproof.

Place tilt motor on right side(from user view, as picture shown)

Camera: Mount the camera on quick release plate, slide it into the fixed plate from left to right, then fix the safety lock while it is in a suitable position.
Smart phone: It needs to attach smart phone adapter(standard accessory) on the quick release plate before mounting smart phone.
Action camera: Before mounting Gopro, tighten T clamp adapter (a standard accessory) on the fixed plate by 1/4inch thumb screw.

Unlock axis motor: G6Max has 3-axis motor locks, unlock the tilt/roll axis to release storage status firstly. Place the cross and slide arm to its working position ,then lock the axis motor for mounting and balancing the camera. Make sure to unlock each axis motor in order when balancing. Please well-balanced the gimbal before powering on.
Tilt axis balance: Follow the balance step as: camera upward balance/forward balance; when the camera can stay still in any angle ,balance is done successfully.
Roll/Pan axis balance: Move the cross arm left-right to balance the axis. Tighten the axis ring when well-balanced.

Long press: Power on/power off
Single tap: Flip to next page of interface (The interface are as per following: Interface 1, which will show the page when we turn the gimbal on; For interface 2 or 3, which could be set up by pushing the joystick to the four direction(up, down, left or right). We could be switch the interface by single tap the power button. When the screen stay in interface 1, we could using the joystick to control the gimbal; And when the screen stay in the interface 2 or 3, the joystick could only select the options, which are including into the menu.)

Single tap: Panning following mode( The default setting)/Locking mode
Double tap: Panning and tilting following mode
Triple tap: All following mode
Note: We could set up the working modes in the App as well.

Single tap: Switch photo/video modes (For mail details, please refer to the camera compatibility list)
Triple tap: Switch to front camera or rear camera

Long press and hold: Fast follow mode (We could set up the other mode in the App), release it to go back to the previous mode
Double tap: Reset
Triple tap: Selfie mode(Reset the gimbal by double tap the trigger button)

3pcs 1/4inch thread hole (2 pcs at the left and right side of handle, 1pcs at the bottom of handle)

There are two ways to connect and control with G6 Max:
WiFi: choose the corresponding brand and model of camera in Feiyu ON App then gimbal can connect to the camera by WiFi. After WiFi connecting successfully, we could control the camera taking picture/recording video/zoom/follow focus.

Shutter release cable: The port for plug with the G6 Max is in Type-C, which is on the front side of the quick release plate, and the other side is plug with the camera.
The shutter release for Sony Cameras is Type-C to Mulit, and the shutter release cable for Panasonic is Type-C to DC2.5mm.
(For more details, please refer to the compatibility list)

Six tap the trigger button, then you will see the display give a message "clean WiFi".
Next, move joystick to the right for confirmation. This operation will clean all wifi connection.

1) Single tap the power button twice, then switch the interface to the interface 2 on the OLED,next select the “ Calibration” option by push the joystick up or down. Confirming the option by push the joystick to the right side
2) The gimbal will automatically check whether be put on a steady flat
3) After the screen shows “Calibration Completed”, pick the gimbal up, click “ESC” on the screen to finish calibration

1) Initialize the gimbal
Single tap the power button twice, then switch the interface to the interface 3 on the OLED,next select the "Initialize option by push the joystick up or down. Confirming the option by push the joystick to the right side, after that, the motors will loose power, wake up the gimbal by single tap the mode button while the OLED show "Tap mode to awake it after INIT"
2) Calibrate the gimble by the "Horizontal Calibration in the App

Feiyu ON App supports firmware upgrades for gimbal, keyboard, and Bluetooth.
After successfully upgrading the firmware through the App, when restarting the gimbal, please press and hold the power button for about 10 seconds and release the button while the gimbal is powered on.

1) Before turn the gimbal on, please make sure all those three axises were balanced properly
2) Please set up the motor strength to "Auto Adaption" : you could single tap the power button, then switch the interface to the page 2 on the OLED, next select the "Auto Adaption" option by push the joystick up or down. Confirming the option by push the joystick to the right side

1) Please make sure three axes were balanced properly and then turn the gimbal on
2) When turning on the gimbal, please DO NOT hold the camera with your hand
3) Please check what causes the vibration. You can identify which motor need to be adjusted in this way: hold one of the motors in working status with your hand, if it stops vibration, that’s the right motor you should reduce the motor strength

Vibration with sound: it is caused by the excessive strength of the motor, which can be solved by reducing the motor strength to fix the weight of the camera and lens.
Vibration without sound: it is caused by the motor strength is too weak, which can be solved by increasing the motor strength to fix the weight of the camera and lens.

1) Turn off the smartphone’s WiFi, and disconnect the camera from other devices, such as the remote control
2) Uninstall the camera app installed on your smartphone
3) Make sure that the password you entered is correct, such as spaces, uppercase and lowercase letters
4) Try to disconnect the WiFi connection of the camera
5) Take out the battery and reinstall it, then restart the gimbal. It's better to reset the camera's WiFi and password, then reconnect